Home > Error Code > Cif Error Code 236

Cif Error Code 236

Contents

a. Note: Dispenser Status (Click Counts) should be run and available before contacting Tech Support 113 Timeout waiting for trailing edge at reject 1. Reset the Cash Dispenser by turning OFF the AC power switch for a few seconds and switching it back ON. If the error does not occur again, put the cash dispenser in service. Check This Out

Once you have completed one of the above(more…) 152 Electronic journal corrupt 1. If the cables are undamaged, the main board or electronic journal may be defective 166 Bad dispense 1. Other components that may cause this error are the main board or the dispensing mechanism. 132 Status reports bad double detect in last dispense 1. Turn the AC power OFF for a few seconds and then back ON to power cycle and reset the cash dispenser. 3. More about the author

Atm Error Codes List

Once the cause has been resolved, place desired cassettes into service and reset the error. The dispenser will shut down, possibly resulting in trailing notes stopping in the path. 1. Verify that the diverter moves freely. 3. Inspect electronic journal to dispenser communication cable for damage.

If the voltages are correct, and the cables are undamaged and correctly connected, causes of this error may be a defective cable, a defective printer, printer control board or the main If these actions have no effect, replace the dispenser 55 RAM corruption A mechanical failure has occurred. If the test dispenses are completed normally, and the return code are correct, clear all errors and place the cash dispenser in operation.b. Triton Error Code 616 The next entry, below 116, is the Hardware Status.

If it is necessary to check continuity of the cable assembly, refer to the appropriate ATM Service Manual for pin out of the cable assembly. 3. Triton Atm Error Codes Otherwise, it may be necessary to replace the dispenser.4. The cables may be defective. 3. my company On all models other then 96XX, Release the printer locking screw.

Inspect the feed path for any jammed notes. Triton Error Code 139 If the error clears, put the cash dispenser in service. 3. Next try a live dispense (note, you can not fully test this dispenser for this error without doing live dispenses). Inspect the cable supplying DC power from the po(more…) 140 Time-out waiting for printer to be ready 1.

Triton Atm Error Codes

A reboot may perhaps be expected. Note: Dispenser Status (Click Counts) should be run and available before contacting Tech Support 126 Diverter moved to reject position during dispense Inspect for a note jam at the diverter. Atm Error Codes List Otherwise, replace the dispenser. 39 Too many notes Clean the all sensors. Triton Error Code 244 If the cables are undamaged, the main board or electronic journal may be defective 155 Electronic journal modify record failure 1.

Our client has some doubts but we, consultants, could not confirm if it is a standard behavior. http://allsoftwarereviews.com/error-code/code-80070424.php Reset the cash dispenser and clear the error. Remove the cassette and inspect for jammed currency in the width sensor and at the output of the cassette. Clean as needed with soft brush and vacuum cleaner. 2. Triton Error Code 151

Release the printer locking screw. Make sure the connectors are seated securely on the main board and on the electronic journal. 2. Make sure the connectors are seated securely on the main board and on the electronic journal. 4. this contact form Inspect electronic journal to dispenser communication cable for damage.

Inspect electronic journal to dispenser communication cable for damage. Atm Error Code 3-da000(80) Other components that may cause this error are the main board or the dispensing mechanism. 134 Exit blocked as reported by status check 1. I checked the Planning Calendar for this Plant using MD27 and also the Valid To is until 2020 which is also fine.   Is there any other place where the Planning

Resource) to Resheduling PPDS Run purpose of Using Primary Resource first then Secoundary ressource,But This Huristic is creating Planned orders when executing the transaction eventough there is  no requirement added  

Contact us about this article Hello Everybody,   I am facing problematic times at the moment in our production site. This will stop the Windows Management Instrumentation Service. Verify that all DC voltages applied to the printer control board are correct. Atm Card Error Codes The dispenser sends this status code when a command has been successfully executed.

If it is necessary to check continuity of the cable assembly, refer to the appropriate ATM Service Manual for pin out of the cable assembly 5. If it is necessary to check continuity of the cable assembly, refer to the appropriate ATM Service Manual for pin out of the cable assembly. 3. Verify that the power supply is operating and the DC voltages being supplied to the main board and dispenser are correct. navigate here The best thing that you can do about this is uninstall or reinstall the program.

Inspect for jammed currency in the feed path and at the Exit sensor. Sorry for the inconvenience. Tricky drives are classified as the most important result in of gradual speeds. A mechanical error has occurred.

Inspect the cable supplying DC power from the power supply to the printer. The maximum withdrawal cannot exceed 50 time the denomination of the bill size in the cassette. 188 PIN working key not configured Enter the management functions and configure (download) the working Should I report this to SAP as bug? 2. Configuration jumpers may have been changed.

If these actions have no effect on dispenser operation, replace the dispenser mechanism and/or the note cassette. If they pass, clear the error and place the ATM in service. 2 If working with a 9100 print a test receipt printer Verify the “Cassette 195 Receipt printer out of Pls note the Error Code = 236 Now the Biz had escalated that this manual reconciliation everyday multiple times is not acceptable. Complete several test dispenses to verify correct operation.

The changed by log shows that it has been done by RFC APO. Otherwise, replace the dispensing mechanism. If error fails to reset, or the error reoccurs in a short amount of time, consider replacing the SPED. 241 SPED Warning: Self Test error See Error Code 240 382 Dispenser no. &1 (matl &2/plant &3) has conversion indicator inAPOGC_ERR_CATEGORY-T_C               APO order with external number does not exist in R/3154      Order with external number &1 (material &2, plant &3) only exists

If these actions have no effect on dispenser operation, replace the dispenser mechanism. Replace the dispensing mechanism. 53 EPROM error A mechanical failure has occurred. Once they are displayed on the screen, print or save them to an external device. If it is necessary to check continuity of the cable assembly, refer to the appropriate ATM Service Manual for pin out of the cable assembly. 3.