After setting the PIN code, wait some seconds before issueing the next command to give the modem some time to register with the GSM network. This value is encoded as follows: 0 - 143 (VP + 1) x 5 minutes 144 - 167 12 Hours + ((VP-143) x 30 minutes) 168 - 196 (VP-166) x 1 Nov 16 18:33:36 frida kernel: [ 164.576115] usb 6-2: USB disconnect, address 2 Nov 16 18:33:38 frida kernel: [ 166.056037] usb 6-2: new full speed USB device using uhci_hcd and address What is an SMS Center / SMSC? 5. check over here
CMS ERROR 29 "Facility rejected" This cause indicates that the facility requested by the Mobile Station is not supported by the PLMN. Starting PPP immediately. --> Starting pppd at Mon Aug 11 22:15:09 2008 --> Pid of pppd: 3057 --> Using interface ppp0 --> pppd: �o��P�@� --> pppd: �o��P�@� --> pppd: �o��P�@� --> OK, driver found ("usb-storage") OK, driver "usb-storage" detached Received inquiry data (detailed identification) ------------------------- Vendor String: USBModem Product String: Disk Revision String: 1.00 ------------------------- Device description data (identification) ------------------------- Manufacturer: USB Thanks, Julian adamantivmAugust 10th, 2008, 06:47 PMHere's a slightly better version, the "> " lines are the ones that were sent to the modem, the rest are replies: > ATE OK http://www.smssolutions.net/tutorials/gsm/gsmerrorcodes/
One other reason for this is your low RAM space. Perhaps that will give an idea of what type of connection needs to happen. A "flip flop" or "multiple device" USB device seems to be a device that can behave as a different USB device at different times, using the same USB connection.
Final Result Code Specific to SMS AT Commands Preferences - Do not show ads The final result codes OK and ERROR are available to all AT commands. Cme Error 3 Any advice, of course, appreciated. Table of +CMS Error Codes and Their Meanings The following table lists some of the +CMS error codes and their meanings. +CMS error code Meaning 300 Mobile equipment (ME) failure. http://smslib.org/doc/gsmerrors/ When the error starts with "+CME ERROR", it means that the error is a device specific error code.
Introduction to AT Commands 15. Cms Error 515 An invalid memory index is assigned to an AT command. Found default devices (1) Accessing device 004 on bus 006 ... Try the following command...
Nick LakeAugust 12th, 2008, 10:59 AMYour way is probably better but I found another way of disabling the flash disk mounting (therefore allowing the USB modem to be detected. http://lsces.co.uk/wiki/Mobile+Device+-+Error+Codes This commands displays the codepages supported by the modem. Cms Error Codes Blue Screen of Death (BSoD) This Cms Error 314 Sim Busy does not pick an operating system to attack, it can happen to all even in the most updated ones. Cms Error 304 Send the following command to the modem to set this parameters: AT+CSMP=17,167,0,16
The AT command +CPIN (command name in text: Enter PIN) can be used to send the PIN to the SIM card. 312 The SIM card requires a PH-SIM PIN to operate. no channel, facility busy/congested etc.). Looking for active driver ... It can be used to create VoIP client and server software. Contact Us! If you wish to get further information, do not hesitate to contact us! Cms Error 50
We try to keep this list up to date, so please send your comments to [email protected] or post them in our forum. I've not tried it and I'm afraid I didn't keep the ref to the original web site but here is the text that I originally cut and paste: ----------------------------------------------------------------------- There is International SMS Messages 9. http://allsoftwarereviews.com/cms-error/cms-error-sim-busy.php People who read this also read...
Silly question but did you set up the connection properly... Gsm Error Codes Developed by GXPMEDIA.COM OZEKI NG SMS Gateway "The World's most reliable SMS gateway software!" [email protected] Tel.: 00 36 52 532 731 Overview Quick start Download Manual How to buy FAQ Contact Comments off November 2016 M T W T F S S « Apr 123456 78910111213 14151617181920 21222324252627 282930 Nội dung quan tâm Nội dung quan tâm Select Category
Basic Concepts of SMS Technology 6. IMSI or directory number is not allocated to a subscriber). The AT command +CPIN (command name in text: Enter PIN) can be used to send the PH-SIM PIN to the SIM card. 313 SIM card failure. 314 The SIM card is Cme Error 50 Third one is the charm, also with 'Init3' commented out: [email protected]:~$ sudo wvdial --> WvDial: Internet dialer version 1.60 --> Cannot get information for serial port. --> Initializing modem. --> Sending:
Scanning your serial ports for a modem. You can also suggest anything that can help us improve this web page. (Optional) Your name: (Optional) Your email address: Due to the amount of messages we received, we may not Please not that in most cases you have only 3 attemps to set the correct PIN code. http://allsoftwarereviews.com/cms-error/cms-error-515-ps-busy.php The fourth parameter contains the DCS (Data Coding Scheme).
We can set this value by changing the fourth parameter of the AT+CSMP command to ‘8': AT+CSMP=1,167,0,8
Introduction to SMS Messaging 2. To enable these extended commands, execute the following commands, or add them to your modems init string: AT+CMEE=1 AT&W Below you can find a list containing almost every error code supported and I couldn't make it works.... That's why most advanced GSM devices support extended errors.
General Syntax of Extended AT Commands 16. CMS ERROR 17 "Network failure". The +CMS ERROR Final Result Code -- Notifies the Occurrences and Causes of Message Service Failures The +CMS ERROR final result code is returned when a message service failure occurs. As it seems to have registered to USB0 can you send AT commands to it?
So the first value should be 1 or higher. Here's the file:
How to Receive SMS Messages Using a Computer / PC? 12. Nick LakeAugust 10th, 2008, 05:27 PMHmmm... TrinhThiYen's Blog Blog at WordPress.com. Shortcut Menu Sponsor Submit a program Contact us SMSSolutions.net Skip Main Navigation Home Freeware Hardware GSM/GPRS Modems GSM/GPRS Modules CDMA Modems CDMA Modules Software SMS/MMS Applications SMS/MMS Gateways SMS Components WAP
After that [...] switches the mode internally, the storage device vanishes [...], and a new device (like an USB modem) shows up I can assert this is the case for me When there is a network error, for instance, when you try to send an SMS message when there is no network coverage, you will receive an error which starts with "+CMS Operating Mode: SMS Text Mode and SMS PDU Mode 21. The modem will respond like this: +CSCS: ("GSM","PCCP437″,"CUSTOM","HEX") If this string contains "HEX" or "UCS2", Unicode seems to be supported.