Home > Citrix Error > Citrix Error 1030 Secure Gateway

Citrix Error 1030 Secure Gateway

I have the appropriate certificate installed/configured. Use Registry Editor at your own risk. Cannot obtain the launch.ica file as this is StoreFront. NetScaler Citrix Advertise Here 694 members asked questions and received personalized solutions in the past 7 days. this contact form

If connecting via the Program Neighbourhood doesn’t pop up ‘protocol driver error’s’, you are sure it must be your CAG/WI setup. (WI=Web Interface) Things to check in your CAG/WI setup: Are For updates to this, go to http://www.citrix.com/download. How would you disable CGP wrapping layer?a Thanks I will look into the NetScaler networking too Yes, disabling session reliability on the Gateway Object in the StoreFront configuration will suffice for Using Registry Editor incorrectly can cause serious problems that might require you to reinstall your operating system. check here

CANCELLARE Citrix Support Automatische Übersetzung Dieser Artikel wurde mit einem automatischen Übersetzungssystem übersetzt und nicht von Personen überprüft. For this functionality to be added, MetaFrame 1.8 Service Pack 1or higher is required. HTH, Tom Tom Shinder [email protected] Microsoft DAIP iX/SCD iX UAG Direct Access/Anywhere Access Group (AAG) The “Edge Man” blog (DA all the time): http://blogs.technet.com/tomshinder/default.aspx Follow me on Twitter: https://twitter.com/tshinder Facebook: http://www.facebook.com/tshinder Users can connect to the affected host internally just fine, it's only when you connect to it via the secure gateway that there is a problem.

All Controllers, Workers, and StoreFront servers need to be resolvable by NetBIOS names and FQDN from a client point of view. As you can see there is no all encompassing solution to this error, instead leaving you to further investigate and keep the aforementioned hints in mind. Here’s how it works: The client establishes a DA connection The user uses the browser to bring up the Citrix Web Interface and authenticates to it. I need to eliminate the CSG this because is causing problems now.

Adjust or remove any TCP KeepAlive settings that may have been added. Not sure I suspect that the NetScalers might have had all 4 STA's on both sites. Several functions may not work. http://discussions.citrix.com/topic/255945-desktop-viewer-error-1030-when-connecting-to-desktop-group/page-2 I have ports 1494, 80, 443 & 2598 from my VIP for Access Gateway open to both DDC - what could I be missing here?

How would you disable CGP wrapping layer?a Thanks I will look into the NetScaler networking too 1337-364036-1870579 Back to top Justin VonWeichardt Members #13 Justin VonWeichardt 30 posts Posted 21 April If using Network Address Translation, refer to CTX039746 – IMA and ICA Browsing With Firewall Address Translation (NAT). A listing of the latest clients and their respective build numbers are available there. 2. They noticed I was using port 80 for xml for xendesktop.

Prior to StoreFront v2.x there was no GUI Option to edit any client-side Proxy Settings for Citrix Receiver, thus leaving you with adjusting the default.ica configuration file. For StoreFront v3.x onwards read this Get 1:1 Help Now Advertise Here Enjoyed your answer? Create a Custom ICA Connection to the published application and attempt the connection. What does CSG post in its logs? 0 LVL 1 Overall: Level 1 Message Author Comment by:PerimeterIT2013-10-01 Comment Utility Permalink(# a39536662) It was working fine till last week, no idea

When coming from the outside I receive the 1030 generic error. http://allsoftwarereviews.com/citrix-error/citrix-error-code-1030.php Highfive and Dolby Voice deliver the best video conferencing and audio experience for every meeting and every room. Thanks! 1316-347286-1794350 Back to top Carl Stalhood CTP Member #2 Carl Stalhood 10,279 posts Posted 23 January 2014 - 04:42 PM 1030 usually means one of the following: STAs are invalid. Have you checked that there is no ACL misconfiguration causing it?

Aaron Brown: hello Carl, I hope you get this but I have a f... Protocol Driver Error CTX130130 – The Protocol Error 1030 is Displayed when Citrix Branch Repeater is Enabled Caution! Server general When you connect to your published application using the Program Neighbourhood till shows ‘protocol driver error’, it must be the load balancer or one of your XenApp servers. http://allsoftwarereviews.com/citrix-error/citrix-error-1030.php I do have 1494 and 2598 open from the VIP to the DDC's though.

b. Check that the subnet mask is consistent on every MetaFrame server in the farm. One of the anomaly is solved by he following article https://www.layer8.one/netscaler-11-ica-proxy-connection-error-0-1030-1110/ 1316-347286-1942809 Back to top Report abuse Back to XenDesktop 7.x Reply to quoted posts Clear Citrix ©1999-2016 Citrix Systems,

During the next outage window I'll try to change the default XML port for all the servers in the cluster and see if that does the trick. 0 LVL 1

Have you checked that there is no ACL misconfiguration causing it? DNS to and from the Secure gateway from the host resolves fine, all servers including the gateway are on the same subnet, no windows firewall or otherwise is in place between ALL COPYRIGHTS AND RIGHTS BELONG TO CITRIX. Ensure that you are using the latest client build.

IP's are pingable. Reply ithamster says: November 17, 2015 at 5:02 am Sohail: Just use Citrix receiver 4(supports ipv6) on the endpoints and configure controllers with Set-BrokerSite -DnsResolutionEnabled 1> Returns DNS hostname instead of All required ports were available, but we missed to enable a successful name resolution mechanism for client computers in the source domain connecting to Citrix resources in the target domain. his comment is here Check and see if the ICA Master Browser Service is started on the server that you are trying to connect to.

Ensure to use the latest IP stack for the client operating system. ------------------------------------------------------------- If all appropriate updates to the server and client are applied, attempt the following items: a. It's been a while since I did CSG but I seem to recall you have to change IIS SSL to another port from 443 - commonly 444 - so that CSG CTX105793 – Error: Cannot connect to the Citrix server.