Home > Cisco Error > Cisco Error No Memory Detected Aborting

Cisco Error No Memory Detected Aborting

At this point I'm pretty sure that it's either dead or I have a lot of bad memory. Recommended Action Make sure the device is functioning and is configured correctly. Recommended Action Call your technical support representative for assistance. Error Message %CBUS-3-CTRLRINITERR: Controller [dec], Error [hex], cdb [hex] [chars] - cbus_init() Explanation A hardware or software error occurred. Check This Out

Error Message %AT-3-MACIPBADCONF: ZONE-NAME: MacIP inoperable configuration, X.X.X.X Explanation If the appletalk event-logging command is configured, this message appears on the console when a MacIP server cannot begin or recover operations No action required. This should prevent a repeat. Error Message %APPN-5-APPNSENDREQ: [chars] Explanation A hardware or software error occurred. This Site

No action required. Recommended Action Notification message only. Close this window and log in. Recommended Action If this message recurs, call your technical support representative for assistance.

Recommended Action This error message should only print when the router is critically short of memory. Error Message %CBUS-3-MEC_OUTHUNG: Interface [chars] output hung, [hex], [chars], [chars] Explanation Output hung on a ciscoBus Ethernet interface. Recommended Action Copy the error message exactly as it appears and report it to your technical support representative. Error Message %AT-3-MACIPNOCABLE: ZONE-NAME: MacIP inoperable IPinterface, X.X.X.X Explanation If the appletalk event-logging command is configured, this message appears on the console when a MacIP server can no longer operate due

Recommended Action Informational message only. If it recurs, a physical network problem in which the nodes cannot hear each other may exist. This can indicate an interface with no cable attached. The remote peer may be misconfigured.

Quote boostinbadger Brain Dumps Smell Bad Join Date Dec 2007 Location Virginia Posts 256 Certifications CCENT - CCNA - WCSP - MCE 11-29-200801:10 AM #4 Are you sure this isn't Error Message %AT-6-NEWNEIGHBOR: [chars]: AppleTalk neighbor added;[node] is operational Explanation The router discovered a new AppleTalk router. Recommended Action Reconfigure the serial interfaces correctly to be a primary and secondary pair. Error Message %AT-6-DELROUTE: AppleTalk network deleted; [atalk_net] removed from routing table Explanation A route aged out of the AppleTalk internetwork.

If this is sporadic, it indicates line noise. http://www.tek-tips.com/viewthread.cfm?qid=1130814 Recommended Action Informational message only. RE: boot issue with cisco 2600 series router popasmuerf (MIS) (OP) 5 Oct 05 13:30 I opened the box up last night and reseated the flash and RAM.....same results.I then removed A search will be made for a valid address.

Join Us! *Tek-Tips's functionality depends on members receiving e-mail. http://allsoftwarereviews.com/cisco-error/cisco-error-46-fix.php BGP Error Messages Border Gateway Protocol error messages Error Message %BGP-3-BADMASK: Attempt to install route for [inet] without valid mask in [chars] Explanation An internal software error occurred. Recommended Action Call your technical support representative for assistance. Quote tiersten was here.

Recommended Action Investigate problem reported in error message. Recommended Action Call your technical support representative for assistance. Recommended Action Call your technical support representative for assistance. http://allsoftwarereviews.com/cisco-error/cisco-error-no-memory-detected-stop.php The system returned: (22) Invalid argument The remote host or network may be down.

The message includes the source of the path, its distance in hops, its metric, and the type of path. Recommended Action Repair or replace the malfunctioning controller. Let me know how you get on.Cheers RE: boot issue with cisco 2600 series router popasmuerf (MIS) (OP) 6 Oct 05 00:08 I was thinking about rmon on my way home

Recommended Action Notification message only.

Error Message %APPN-6-APPNSENDMSG: [chars] Explanation A hardware or software error occurred. Error Message %AT-6-NEWZONE: AppleTalk zone added; zone [chars] defined Explanation A new AppleTalk zone has been created. Recommended Action Reduce other system activity to ease memory demands. This is typically the result of user intervention in BSTUN reconfiguration or disabling.

Error Message %APPN-3-APPNERR: [chars] Explanation A hardware or software error occurred. RE: boot issue with cisco 2600 series router popasmuerf (MIS) (OP) 1 Oct 05 17:45 Yeah, that is what I was thinking (as far as reseating the flash and RAM)The router DOING SYSTEM RESET. navigate here Recommended Action Call your technical support representative for assistance.

This condition is a result of one of the following: the daughter card did not reset, or the microcode on the card is in a hung state, or the card cannot Error message should indicate the problem. Error Message %AT-6-ROUTEDOWN: [chars]: AppleTalk network down; port to [atalk_net] disabled Explanation A connected route is being advertised as down (also known as notify neighbor) because the configured port is no It would enter setup mode.

Error Message %CBUS-3-TXALLOC: Error ([hex]) tx_allocate - cbus_init() Explanation A hardware device did not respond appropriately to a request. No action required. Chances are its broken anyway. I may be wrong here, but shouldn't the router also enter setup mode if startup config is empty?

The system returned: (22) Invalid argument The remote host or network may be down. Recommended Action The system recovered by generating an error code to the requester. Error Message %ARAP-3-BADCONFIG: TTY [dec]: unhandled configuration command Explanation A configuration command was not recognized. No action required.